By: DRP Enterprise Inc.

Click To Add This Page To Your Favorites                                                     1-866-377-8665 8:00 AM - 5:00 PM EST.
 

 

 

Equipment Checklist

Before beginning your project, make sure you have all the right equipment and products.

1. Use the Equipment List below to ensure you have all the right tools.

2. Identify the proper products needed for your specific project by using the Product Checklist along with the Diamond Disc Selection Guides.

Product Checklist

Whether you’re processing New Polish Marble Pool Finish or repairing a Rough Over-Exposed Quartz Finish, there are 2 steps for which you will need products:

Step 1    Surface Preparation

Step 2    Final Finish.

Selection of which Diamond Disc type and grit to use is determined by reading Surface Processing, Final Finish and Diamond Disc Selection Guides. This checklist will help you determine what product you will need to order.

Surface Preparation

 

New Polish Marble Pool Finish

Step 1 surface preparation after the proper acid (a good acid wash before insures a nice polish finish without a cloudy look) wash start with Aqua Hone Diamond Disc (HD7030, HD7050, HD7070). This removes any rough edges while preparing the surface for step 2 finial finish.

Step 2  Change aqua disc to Aqua Hone Diamond Disc (HD7120 or HD7220)

Rough Pool Surfaces

The Diamond Disc product for step 1 surface preparation, are either Cut Diamond (CD7030-70). Carefully select the proper diamond disc type and grit for your application from our Diamond Disc Selection Guides, using the coarse grit for real rough finish to medium grit for semi-rough finish. This removes any rough edges while preparing the surface for step 2 final finish. Click on to see Diamond Disc Selection Guides  for proper diamond type and grit.

Final Finish

The Final Finish Process starts with changing to the correct Diamond Disc, using Hone Diamond or Dual Diamond. Click on to see Diamond Disc Selection Guides  for proper diamond type. Start with recommended disc doing small areas on the wall. As you process, check the surface with your hand as you go making sure not to leave any non polished surface behind. Continue using this technique to complete the entire swimming pool. By starting with the walls first and proceeding to the floors allows most residue to drain to the bottom of pool. After the pool is complete and all surface are finished use the garden hose to wash down any existing residue. Use a sump pump to remove and discharge all wash down solution.

 

Click On Picture

Walls & Floors

Process about 4 square feet before stopping machine and feeling the surface you just processed. If you can feel areas that are smoother then others, make another pass with machine. You want the surface to feel uniform in texture through out.

 

 
 

Click On Picture

Inside Step Radius

To perform this procedure change your backer pad on machine from 7" PN7519 to 5" PN5519. Attach HD7070 diamond pad to the center of the 5" backer pad making sure the water through hole in the backer pad is clear. Click on to see Diamond Disc Selection Guides  for proper diamond grit.

 

 
 

Click On Picture

Inside Step Radius

The flexibility of our Hone Diamond disc attached to our PN5519 allows for the inside step radius to be processed easy. Click on to see Diamond Disc Selection Guides  for proper diamond grit. As shown in the picture the 1" over lap rolls up the inside radius polishing as you move along the step

 
 

Click On Picture

Cove

The coves are processed using the same technique as inside radius.

 
 

Click On Picture

Waterline & Tile

This area should be processed last, taking your time polishing the edge as you move along the waterline tile. The machine being light, weighing just 6 LBS prevents user fatigue.

See Diamond Disc Selection Guides  for proper diamond type and grit.

 

 

 

DRP Enterprise Inc. 6401 E. Rogers Cir. #2 Boca Raton, Fl. 33487

 Mail To: Pool Tool Information

Tile Specifications.